How many 24" × 48" pieces can you cut from a 4×8 sheet?
You can cut 3 pieces of 24" × 48" from one 4×8 sheet (48" × 96") with a 1/8" saw kerf and rotation allowed — 75% of the sheet ends up in parts. Sizes like this are typical for quarter-sheet panels.
The layout is a straight grid, 1 across and 3 along the length, every part turned across the sheet. 75% is a solid yield for a single part size; 25% goes to kerf and offcut.
Kerf and grain
On paper the sheet holds 4, but that is the no-kerf answer. Two 24" parts add up to exactly the sheet's 48", so there is no room left for even one 1/8" saw cut between them. Cut the parts at 23-7/8" × 48" instead and you get all 4 back.
Rotation is doing real work. With the grain locked, so every part's 48" side runs along the sheet's 96" length, only 1 fit — the other 2 come from turning parts across the sheet. That's fine for paint-grade plywood, MDF or melamine; for show faces with visible grain, plan on 1 per sheet.
| Saw kerf | Rotation allowed | Grain-locked (no rotation) |
|---|---|---|
| 1/8" | 3 · 75% | 1 · 25% |
| None (theoretical) | 4 · 100% | 4 · 100% |
How many sheets for a batch?
| Pieces needed | 4×8 sheets | Last sheet |
|---|---|---|
| 10 | 4 | 1 of 3 — room for 2 more |
| 25 | 9 | 1 of 3 — room for 2 more |
| 50 | 17 | 2 of 3 — room for 1 more |
Same 1/8" kerf, rotation allowed. A part-filled last sheet is the place to nest drawer bottoms, shelves or anything else from the same material.
FAQ
How many 24x48 pieces can you cut from a 4×8 sheet?
You can cut 3 pieces of 24" × 48" from one 4×8 sheet (48" × 96") with a 1/8" saw kerf and rotation allowed — 75% of the sheet ends up in parts. The layout is a straight grid, 1 across and 3 along the length, every part turned across the sheet.
Why only 3 and not 4?
On paper the sheet holds 4, but that is the no-kerf answer. Two 24" parts add up to exactly the sheet's 48", so there is no room left for even one 1/8" saw cut between them. Cut the parts at 23-7/8" × 48" instead and you get all 4 back.
Does grain direction change how many 24" × 48" pieces fit?
Rotation is doing real work. With the grain locked, so every part's 48" side runs along the sheet's 96" length, only 1 fit — the other 2 come from turning parts across the sheet. That's fine for paint-grade plywood, MDF or melamine; for show faces with visible grain, plan on 1 per sheet.
How this was worked out
EZNESTING's nesting engine (the same one the optimizer runs, in its default least-waste guillotine mode) was given more 24" × 48" parts than could possibly fit on one 48" × 96" sheet, with a 1/8" kerf between parts and none at the factory edges. The parts it placed are the answer. That count is checked against simple grid layouts in both orientations (best of those: 3), so the page never shows less than a straight grid would give. No edge trim is assumed; if you skim 1/4" off a factory edge, re-run it in the optimizer with trim set.
Nearby sizes
- 30" × 48" from a 4×8 sheet — 3 per sheet
- 24" × 36" from a 4×8 sheet — 3 per sheet
- 22" × 36" from a 4×8 sheet — 5 per sheet
- 36" × 48" from a 4×8 sheet — 2 per sheet
Try any size in the sheet yield calculator, or lay out a full cut list with the plywood cut list optimizer, the 4×8 plywood cut calculator or the nesting optimizer.